CareFusion Bird Sentry Guía de usuario

Bird Sentry™ Blender User’s Guide

Bird Sentry™ Blender x L1383 Rev. D Bird Sentry™ Blender

Bird Sentry™ Blender L1383 Rev. D xi Contents Revision History ...

Bird Sentry™ Blender xii L1383 Rev. D Chapter 7: Appendices ...

Bird Sentry™ Blender L1383 Rev. D 1 Chapter 1: Introduction The Bird Sentry blender is a compact air/oxygen gas mixing device which incorporates the

Chapter 1: Introduction Bird Sentry™ Blender 2 L1383 Rev. D Front Panel Functional Description A Display A digital liquid crystal display provi

Bird Sentry™ Blender Chapter 1: Introduction L1383 Rev. D 3 F Calibrate Key When the keypad is unlocked, the CAL key is used in conjunction with

Chapter 1: Introduction Bird Sentry™ Blender 4 L1383 Rev. D N Low Alarm Display Control The low alarm setting is displayed at all times just be

Bird Sentry™ Blender Chapter 1: Introduction L1383 Rev. D 5 B Outlet Port See Figure 1, letter O. C O2 Sensor Port A sampling port for the oxyg

Chapter 1: Introduction Bird Sentry™ Blender 6 L1383 Rev. D What You Will Need to Operate the Blender ● Pressurized Oxygen. The compressed oxyge

Bird Sentry™ Blender L1383 Rev. D 7 Chapter 2: Operating Procedures Before placing the Bird Sentry blender into clinical use, the performance check

Bird Sentry™ Blender ii L1383 Rev. D This document is protected by United States and International Copyright laws. This document may not be cop

Chapter 2: Operating Procedures Bird Sentry™ Blender 8 L1383 Rev. D High Alarm Setting To adjust the high alarm setting: 1. Press the LOCK key

Bird Sentry™ Blender Chapter 2: Operating Procedures L1383 Rev. D 9 Calibration Procedures The Bird Sentry blender should be calibrated before be

Chapter 2: Operating Procedures Bird Sentry™ Blender 10 L1383 Rev. D Automatic Calibration to Room Air The Bird Sentry blender can be quickly ca

Bird Sentry™ Blender L1383 Rev. D 11 Chapter 3: Pressure Differential Alarm/Bypass Check Before placing the Bird Sentry blender into clinical use, p

Chapter 3: Pressure Differential Alarm/Bypass Check Bird Sentry™ Blender 12 L1383 Rev. D PROCEDURE BIRD SENTRY™ RESPONSE 11. Slowly raise the

Bird Sentry™ Blender L1383 Rev. D 13 Chapter 4: Troubleshooting Problem Potential causes and solutions Oxygen concentration discrepancy between ox

Chapter 4: Troubleshooting Bird Sentry™ Blender 14 L1383 Rev. D Problem Potential causes and solutions Sensor will not calibrate. 1. Sensor c

Bird Sentry™ Blender L1383 Rev. D 15 Chapter 5: Cleaning the Bird Sentry™ Blender Warning! Explosion hazard. DO NOT gas sterilize the Bird Sentry bl

Chapter 5: Cleaning the Bird Sentry™ Blender Bird Sentry™ Blender 16 L1383 Rev. D Bird Sentry™ Blender

Bird Sentry™ Blender L1383 Rev. D 17 Chapter 6: Servicing and Maintaining the Bird Sentry™ Blender Warning! There are no user-serviceable components

Bird Sentry™ Blender L1383 Rev. D iii Revision History Date Revision Description February 1997 A Initial release. March 1997 B January 1998

Chapter 6: Servicing and Maintaining the Bird Sentry™ Blender Bird Sentry™ Blender 18 L1383 Rev. D To replace the Disposable Galvanic O2 Sensor.

Bird Sentry™ Blender L1383 Rev. D 19 Chapter 7: Appendices Glossary Term Description Air/ O2 Mixture of compressed air and oxygen °C Degrees Cel

Chapter 7: Appendices Bird Sentry™ Blender 20 L1383 Rev. D Mixed gas stability* ±1% oxygen Ambient operating conditions Temperature range 59 to

Bird Sentry™ Blender Chapter 7: Appendices L1383 Rev. D 21 Note: All specifications assume the following standard environmental conditions unless

Chapter 7: Appendices Bird Sentry™ Blender 22 L1383 Rev. D Bird Sentry™ Blender Setup The Bird Sentry blender is easily setup and adapts to most h

Bird Sentry™ Blender Chapter 7: Appendices L1383 Rev. D 23 Mixing Operation The Bird Sentry blender is designed to utilize two (2) 50 PSIG (3.4 B

Chapter 7: Appendices Bird Sentry™ Blender 24 L1383 Rev. D Electrical Block Diagram This diagram is intended to assist the user in understanding

Bird Sentry™ Blender Chapter 7: Appendices L1383 Rev. D 25 Flow Characteristics Note: Graphs are typical of a representative sample. Minor varia

Chapter 7: Appendices Bird Sentry™ Blender 26 L1383 Rev. D Bird Sentry™ Blender

Bird Sentry™ Blender L1383 Rev. D 27 Index A alarm bypass function, 23 pressure differential, 11 setup procedure, 7 specifications, 20 alarms and co

Bird Sentry™ Blender iv L1383 Rev. D Warranty THE BIRD SENTRY™ BLENDER IS WARRANTED TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP AND TO

Chapter 7: Appendices Bird Sentry™ Blender 28 L1383 Rev. D Bird Sentry™ Blender

Bird Sentry™ Blender L1383 Rev. D v EMC Notice This equipment generates, uses, and can radiate radio frequency energy If not installed and used in a

Bird Sentry™ Blender vi L1383 Rev. D Read this entire manual before attempting to operate or service the Bird Sentry™ blender: Attempting to op

Bird Sentry™ Blender L1383 Rev. D vii Safety Information Review the following safety information before operating the Bird Sentry blender: Definitio

Bird Sentry™ Blender viii L1383 Rev. D ● DO NOT tape, obstruct or remove the reed alarm during clinical use. ● DO NOT occlude the sensor port

Bird Sentry™ Blender L1383 Rev. D ix ● Users are advised to use pressure regulators, set to 50 ±5 PSIG(3.4± .4 BAR), which display system pressure.